The feasibility of obtaining cellulose acetate from lignocellulosic precursors is of great interest from the environmental, economic and technological points of view. Herein, sugarcane bagasse and vegetable sponge (Luffa cylindrica ) were used as precursors to produce cellulose using the organosolv extraction procedure. From the extracted celluloses, the production of cellulose acetate was carried out by the homogeneous acetylation method. The obtained materials were characterized by FTIR, solid-state 13C NMR, XRD, TG and DSC techniques. The results revealed the success of both the extraction and the acetylation processes, which provided cellulose with high crystallinity and cellulose acetates with high degrees of substitution (cellulose triacetates).

Hydrocarbons present in saturated fractions of crude oils can be assessed by atmospheric pressure chemical ionization (APCI) using small hydrocarbons as ionizing reagents in a Fourier transform ion cyclotron resonance mass spectrometer (FT-ICR MS). In this work, five paraffin standards of different average molar mass distributions (Mw) were easily ionized by APCI(+)FT-ICR MS using isooctane as the reagent gas. Data of Mw, carbon number and double bond equivalent (DBE) distributions corresponding to linear and cyclic hydrocarbons (HCs) were compared to results obtained from analysis of high temperature gas chromatography with a flame ionization detector (HTGC-FID), comprehensive two-dimensional gas chromatography coupled to mass spectrometry (GC×GC-MS) and 1H and 13C nuclear magnetic resonance (NMR) spectroscopy. APCI(+)FT-ICR MS data showed good agreement with those of analytical techniques. Furthermore, the ability of APCI(+) to assess n-paraffin, even in blends with polyaromatic hydrocarbon molecules such as coronene (Mw = 301 Da) at concentrations from 2.5 to 25 µg mL-1, was demonstrated. The typical MS paraffin profile (containing repeating mass units of 14 Da) was clearly confirmed, being totally suppressed when a concentration of 25 µg mL-1 of coronene was used. This phenomenon was also evidenced in one of two saturated fractions produced using saturates, aromatics and polar (SAP) compound fractionation methodology.

The influence of the structural and microstructural characteristics of graphitic precursors on the production of graphite oxide (GO) is investigated in the present work. Six different graphitic precursors were used to produce GO following a modified Hummers method, namely: natural graphite, commercial lubricant graphite, milled graphite, graphite flakes, high-purity graphite and graphite recycled from Li-ion batteries. The products were characterized by X-ray diffraction (XRD), thermogravimetry, solid-state 13C nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). 13C NMR spectra revealed the presence of epoxy, hydroxyl, carbonyl and lactol groups in the synthesized GOs. However, the oxidation degree of each product was found to be dependent on the average crystallite size (Lc) and particle size of the graphitic precursors, with the best GO samples being produced from the milled graphite and the graphite recycled from ion-Li batteries. These results were rationalized in terms of the structural and microstructural differences among the graphitic precursors, as revealed by the XRD patterns and SEM images, evidencing the importance of the correct choice of the precursor aiming the achievement of a well-developed structure for the GO product.

To choose among the variety of oleaginous plants for biodiesel production, the oil content of several matrices was determined through different low-field ¹H nuclear magnetic resonance (NMR) experiments with varied pulse sequences, namely single-pulse, spin-echo, CPMG, and CWFP. The experiments that involved the first three sequences showed high correlation with each other and with the solvent extraction method. The quality of the vegetable oils was also evaluated on the basis of the existing correlation between the T2 values of the oils and their properties, such as viscosity, iodine index, and cetane index. These analyses were performed using HCA and PCA chemometric tools. The results were sufficiently significant to allow separation of the oleaginous matrices according to their quality. Thus, the low-field ¹H NMR technique was confirmed as an important tool to aid in the selection of oleaginous matrices for biodiesel production.

Rice husk ash (RHA) is used as a silica source for several purposes, among them to obtain metal catalysts, as was done in this work. The catalysts were characterized by chemisorption, physisorption, thermal analyses (TG, DSC), X-ray diffraction, X-ray fluorescence, temperature-programmed reduction and scanning electron microscopy. The catalysts synthesized with different Ni loadings supported on RHA were applied to the reaction of dry reforming of methane. The reaction was tested at three temperatures of catalytic reduction (500, 600 and 700 ºC). All synthesized catalysts were active for the studied reaction, with different H2/CO ratios achieved according to degree of metallic dispersion.

Silica obtained from rice husk after acid leaching and calcination was compared to commercial silica as a catalyst support. CaO and SnO2 catalysts were prepared by impregnation and tested in the transesterification of soybean oil and the esterification of oleic acid. CaO catalysts showed basic character and were the most active for transesterification, whereas SnO2 catalysts were acid and the most effective for esterification. In both cases the performances of the catalysts prepared with rice husk ash and commercial silica were similar. These results demonstrate that rice husk is a cost-effective and environmentally-friendly source of silica that can be used as a catalyst support.

FeBr2 has reacted with an equivalent of mnt2- (mnt = cis-1,2-dicyanoethylene-1,2-dithiolate) and the α-diimine L (L = 1,10'-phenantroline, 2,2'-bipyridine) in THF solution, and followed by adding of t-butyl-isocyanide to give [Fe(mnt)(L)(t-BuNC)2] neutral compound. The products were characterized by infrared, UV-visible and Mössbauer spectroscopy, besides thermogravimetric and conductivity data. The geometry in the equilibrium was calculated by the density functional theory and the electronic spectrum by the time-dependent. The experimental and theoretical results in good agreement have defined an octahedral geometry with two isocyanide neighbours. The π→π* intraligand electronic transition was not observed for cis-isomers in the near-IR spectral region.

The present work investigated the effect of coprecipitation-oxidant synthesis on the specific surface area of perovskite-type oxides LaBO3 (B= Mn, Ni, Fe) for total oxidation of ethanol. The perovskite-type oxides were characterized by X-ray diffraction, nitrogen adsorption (BET method), thermogravimetric analysis (TGA-DTA), TPR and X-ray photoelectron spectroscopy (XPS). Through method involving the coprecipitation-oxidant was possible to obtain catalysts with different BET specific surface areas, of 33-51 m²/g. The results of the catalytic test confirmed that all oxides investigated in this work have specific catalytic activity for total oxidation of ethanol, though the temperatures for total conversion change for each transition metal.

We report a structural study on polycrystalline La0.86Sr0.14Mn1-y Cu yO3+delta samples (y = 0, 0.05, 0.10, 0.15, 0.20) using refinement of powder X-ray diffraction data and analysis of scanning electron microscopy images. It is found that the structure remains rhombohedral through the whole series, with a decrease in the average Mn-Mn bond distances, slight variations in Mn-O-Mn angle and reduction in the unit cell volume with increasing Cu amounts. The values of Mn-Mn distances suggest compact structures with d within ±1%. Scanning electron microscopy images reveal homogeneous microstructure in all samples, besides a trend for smaller grains and larger porosity with increasing Cu content.

This work consists in a study about the chemical activation of charred rice hulls using NaOH as the activation agent. The influence of the naturally-occurring silica was particularly evidenced. X-ray diffraction patterns showed the formation of sodium carbonate and silicates in the activated samples, whereas thermogravimetric curves revealed a strong reduction in the ash content of these samples after washing with water. Nitrogen adsorption data indicated a microporosity development only in the washed samples, with BET surface area values of 450 and 1380 m²/g achieved for the samples activated at 800 °C starting from the precursor with or without silica, respectively.

FeBr2 reacts with the S2C2(CN)2(2-) ion (1:1 ratio) in the presence of an excess of t-BuNC in THF to give the mixed ligand [Fe(S2C2(CN)2)(t-BuNC) 4] compound. This neutral product with a formal oxidation state of two for the iron atom was characterized by conductivity measurements, and, i.r., Mössbauer, 13C and ¹H n.m.r. spectroscopy. There is a Fe-C pi back-donation strengthened towards isocyanide ligands, according to the data of 13C, ¹H n.m.r. and Mössbauer spectroscopy.

Discutimos detalhadamente a solução de um problema originalmente proposto para um examevestibular, envolvendo a oscilação de um sistema massa-mola num referencial acelerado e a determinação da amplitude de oscilação a partir do instante em que cessa a aceleração do referencial.Mostramos que o valor dessa amplitude depende essencialmente da relação entre o tempo duranteo qual permanece a aceleração do referencial e o período de oscilação. Na situação limite em queo período de oscilação é muito maior do que o tempo de aceleração, o sistema aproxima-se de umsistema conservativo e a amplitude de oscilação pode ser determinada por conservação da energiamecânica. O problema apresentado constitui um interessante exercício para a discussão (em nívelmédio ou universitário) de temas como forças fictícias, mudanças de coordenadas e não-conservaçãode energia mecânica em referenciais não-inerciais.

The detailed solution of a problem originally proposed for a college-admission exam is discussed.The problem involves the oscillation of a mass-spring system in an initially accelerated referentialand the determination of the amplitude of vibration after the referential has reached the rest.We show that the value of this amplitude depends essentially on the relation between the timeof acceleration and the period of oscillation. In the limit case when the period of oscillation ismuch longer than the time of acceleration, the system approaches a conservative system and theanswer can be found by applying the principle of conservation of mechanical energy. The presentedproblem constitutes an interesting exercise for the discussion (at either high-school or college level)of subjects like fictitious forces, coordinates change, and non-conservation of mechanical energy innon-inertial reference systems.